講講電線電纜基本知識

Talk about the basic knowledge of wire and cable

電線電纜制造流程概述

Overview of wire and cable manufacturing process

講講電線電纜的制造與大多數機電產品的生產方式是完全不同的。機電產品通常采用將另件裝配成部件、多個部件再裝配成單臺產品，產品以臺數或件數計量。電線電纜是以長度為基本計量單位。所有電線電纜都是從導體加工開始，在導體的外圍一層一層地加上絕緣、屏蔽、、成纜、護層等而制成電線電纜產品。產品結構越復雜，疊加的層次就越多。

The manufacture of wire and cable is quite different from that of most mechanical and electrical products. Mechanical and electrical products are usually assembled into components and multiple components to be reassembled into single products. The products are measured by number or number of pieces. Wire and cable are based on the length of the basic unit of measurement. All wires and cables start from conductor processing. They are made up of insulation, shielding, cable and protective layer on the outer side of the conductor, and are made into wire and cable products. The more complex the product structure, the more layers are superimposed.

一、電線電纜產品制造的工藝特性：

1. The technological characteristics of the manufacture of wire and cable products:

1．大長度連續疊加組合生產方式

Continuous superposition combined production mode of 1. large lengths

大長度連續疊加組合生產方式，對電線電纜生產的影響是全局性和控制性的，這涉及和影響到：

The influence of the continuous superposition of large length combined production on the production of wire and cable is global and controlled, which involves and affects:

（1）生產工藝流程和設備布置

(1) production process and equipment layout

貴州電線電纜認為生產車間的各種設備必須按產品要求的工藝流程合理排放，使各階段的半成品，順次流轉。設備配置要考慮生產效率不同而進行生產能力的平衡，有的設備可能必須配置兩臺或多臺，才能使生產線的生產能力得以平衡。從而設備的合理選配組合和生產場地的布置，必須根據產品和生產量來平衡綜合考慮。

All kinds of equipment in the production workshop must be reasonably discharged according to the technological process required by the product, so that the semi finished products of each stage will be transferred in a smooth way. The equipment configuration should balance the production capacity considering the different production efficiency. Some devices may have two or more units to balance the production capacity of the production line. Therefore, the rational selection and combination of the equipment and the layout of the production site must be taken into account according to the balance of the product and production.

（2）生產組織管理

(2) production organization and management

生產組織管理必須科學合理、周密準確、嚴格細致，操作者必須一絲不茍地按工藝要求執行，任何一個環節出現問題，都會影響工藝流程的通暢，影響產品的質量和交貨。特別是多芯電纜，某一個線對或基本單元長度短了，或者質量出現問題，則整根電纜就會長度不夠，造成報廢。反之，如果某個單元長度過長，則必須鋸去造成浪費。

The organization and management of production must be scientific, reasonable, precise, precise and meticulous. Operators must be meticulous in accordance with the requirements of the process. Any part of the problem will affect the smooth process and affect the quality and delivery of products. In particular, multi core cable, a line pair or basic unit length is short, or quality problems, the whole cable will not be long enough to cause scrap. On the other hand, if the length of a unit is too long, it must be sawn to cause waste.

（3）質量管理

(3) quality management

大長度連續疊加組合的生產方式，使生產過程中任何一個環節、瞬時發生一點問題，就會影響整根電纜質量。質量缺陷越是發生在內層，而且沒有及時發現終止生產，那么造成的損失就越大。因為電線電纜的生產不同于組裝式的產品，可以拆開重裝及更換另件；電線電纜的任一部件或工藝過程的質量問題，對這根電纜幾乎是無法挽回和彌補的。事后的處理都是十分消極的，不是鋸短就是降級處理，要么報廢整條電纜。它無法拆開重裝。

The production mode of continuous superposition of large length makes any link and instantaneous problem in the production process will affect the quality of the whole cable. The more the quality defects occur in the inner layer, and the loss of production is not found in time, the greater the loss. Because the production of wire and cable is different from the assembled products, it can be reassembled and replaced. The quality problem of any part or process of wire and cable is almost irreparable to the cable. The aftertreatment is very negative, not the sawing or the downgrade, or the whole cable. It can't be reassembled.

電線電纜的質量管理，必須貫串整個生產過程。質量管理檢查部門要對整個生產過程巡回檢查、操作人自檢、上下工序互檢，這是保證產品質量，提高企業經濟效益的重要保證和手段。

Wire and cable quality management, must run through the entire production process. The inspection department of quality control should inspect the whole production process, inspect the operator and check the process with each other, which is an important guarantee and means to ensure product quality and improve the economic efficiency of enterprises.

2．生產工藝門類多、物料流量大

2. the production process is large and the material flow is large

電線電纜制造涉及的工藝門類廣泛，從有色金屬的熔煉和壓力加工，到塑料、橡膠、油漆等化工技術；纖維材料的繞包、編織等的紡織技術，到金屬材料的繞包及金屬帶材的縱包、焊接的金屬成形加工工藝等等。

Wire and cable manufacturing process involved a wide range of categories, from non-ferrous metal smelting and pressure processing, plastic, rubber, paint and other chemical technology; fiber material winding, weaving and other textile technology, metal materials and metal strip wrapped package, longitudinal welding metal forming process and so on.

電線電纜制造所用的各種材料，不但類別、品種、規格多，而且數量大。因此，各種材料的用量、備用量、批料周期與批量必須核定。同時，對廢品的分解處理、回收，重復利用及廢料處理，作為管理的一個重要內容，做好材料定額管理、重視節約工作。

All kinds of materials used in the manufacture of wire and cable are not only types, varieties and specifications, but also large quantities. Therefore, the amount of material, the amount of preparation, the period of batch and the batch must be approved. At the same time, the decomposition, recovery, reuse and waste disposal of waste products as an important part of management, we should do well in material ration management and pay attention to saving work.

電線電纜生產中，從原材料及各種輔助材料的進出、存儲，各工序半成品的流轉到產品的存放、出廠，物料流量大，必須合理布局、動態管理。

In the production of wire and cable, the flow and storage of raw materials and auxiliary materials, the transfer of semi-finished products from each process to the storage and export of products, and the large volume of material must be rationally distributed and dynamically managed.

3．專用設備多

3. special equipment many

電線電纜制造使用具有本行業工藝特點的專用生產設備，以適應線纜產品的結構、性能要求，滿足大長度連續并盡可能高速生產的要求，從而形成了線纜制造的專用設備系列。如擠塑機系列、拉線機系列、絞線機系列、繞包機系列等。

Wire and cable manufacturing, using special production equipment with characteristics of the industry, is suitable for the structure and performance requirements of cable products, and meets the requirements of continuous and high-speed production with large length, thus forming a series of special equipment for cable manufacturing. Such as extruding machine series, wire drawing machine series, stranded machine series, wrapping machine series and so on.

電線電纜的制造工藝和專用設備的發展密切相關，互相促進。新工藝要求，促進新專用設備的產生和發展；反過來，新專用設備的開發，又提高促進了新工藝的推廣和應用。如拉絲、退火、擠出串聯線；物理發泡生產線等專用設備，促進了電線電纜制造工藝的發展和提高，提高了電纜的產品質量和生產效率。

The manufacturing process of wire and cable is closely related to the development of special equipment, and it promotes each other. New technology is required to promote the production and development of new special equipment; in turn, the development of new special equipment has promoted the promotion and application of new technology. Such as wire drawing, annealing, extrusion series line, physical foaming production line and other special equipment, promote the development and improvement of wire and cable manufacturing technology, and improve the quality and efficiency of cable products.

二、電線電纜的主要工藝

Two. The main process of wire and cable

電線電纜是通過：拉制、絞制、包覆三種工藝來制作完成的，型號規格越復雜，重復性越高。

Wire and cable are made through three processes: drawing, hanging, and coating. The more complex the model and the specification, the higher the repeatability.

1．拉制

1. drawing

在金屬壓力加工中.在外力作用下使金屬強行通過模具（壓輪）,金屬橫截面積被壓縮,并獲得所要求的橫截面積形狀和尺寸的技術加工方法稱為金屬拉制。

In metal pressure processing, the technological processing method of metal forcing through metal mold (pressing wheel), cross section area of metal and obtaining the required cross-sectional area and shape and size under external force is called metal drawing.

拉制工藝分：單絲拉制和絞制拉制。

Drawing process: single wire drawing and stranding.

2．絞制

2. stranded system

為了提高電線電纜的柔軟度、整體度，讓2根以上的單線，按著規定的方向交織在一起稱為絞制。

In order to improve the softness and integrity of the wire and cable, more than 2 single lines are interwoven in the prescribed direction, which is called the winch.

絞制工藝分：導體絞制、成纜、編織、鋼絲裝鎧和纏繞。

Stranding process: conductor stranding, cabling, weaving, and winding steel wire armoring.

3．包覆

3. cover

根據對電線電纜不同的性能要求，采用專用的設備在導體的外面包覆不同的材料。包覆工藝分：

According to the different performance requirements of wire and cable, special equipment is used to cover different materials outside the conductor. The coating process is divided into three parts:

A．?dāng)D包：橡膠、塑料、鉛、鋁等材料。

A. extrusion package: rubber, plastic, lead, aluminum and other materials.

B．縱包：橡皮、皺紋鋁帶材料。

B. longitudinal bag: rubber, wrinkled aluminum belt material.

C．繞包：帶狀的紙帶、

C. around the bag: strip of paper tape,